iagent - User contributions [en]

Voron 0.1

2026-10-14T16:59:07Z

Maintenance script: Voron 0.1: list the Revolt A2 and Resend A2 from the wire diagram

Using Recore A8 and Retool A2 in a Voron 0.1. This page is a work in progress.

See also [[Voron 2.4]] for the same boards in a larger Voron.

==Hardware==
* [[Recore A8]] as the main board
* [[Retool A2]] as the USB toolhead board (extruder, hotend heater and thermistor, fans, accelerometer, Neopixel)
* [[Revolt A2]] for the X and Y steppers (two TMC5160 drivers)
* Resend A2, which carries the USB connection and power to the toolhead
== Rewire diagram==
[[https://rewire.iagent.no/#cfg=zH4sIAAAAAAAAA4VVy06kQBTd-xWVuK1k6l0FO51p42QSNWLrkjDd1UqCQADH1sV8-1yqeE5DXDQNt86599wXnP9FlX1PK4sui6Tax_d2V1Q2vjDoLd0jipIGBZJiZSSqigaRs_MTQlMUWXzBHIG1BGoUx5obz4BrZpE9NtXb3lYL_Nrm-57PHV9ohrUMViP-KbKmZwgnEQJSwsgJI2psWdrKIaVHakypDqbaag-KjxPiBjTVTVE6pvJZEYmNFo7J9FoU7bBEkzaMXgrzsRbGeCqjWOrTVK6SPL7MinfwIMjrq2MEjqGZxoFQjgEqfbQyqZr_2AONur7SwMiB17FeiqbtxiHJV9KjfYcpDpj6osM3xednZuMfVfJc5Ifsw3vwPdZUYtWnue7BFmV6tFlcp_kzQJwD6dVLhZXoK3zI0hLRtcrSriswJlKzaczjSp4wSy2DawGDJclSHz_5F0KZnxvKBJYL-xPZXZMWefwrze1r0qS72rO8VqYYFuqUdRdtPcxNC-McUGRhJr9THh_eaq-Eu5obcEmZOXHJGHmM6_e02b14tNsppSWg9Qn62iaN3ce_4cfEoyf4jsAYmpkUh-fhNrqMb7cPBDF3-_NmPBRhpJAMo9Giwk3UIjcRnaI00lMUC68oCsKrmYVBrecm8ETZnHcNJg7XwQRPTtrDFHWzufWSqXT3U800jBjMx9QtBbnsW0ei0PgFkkv9VnT1mJ7x8O7pHiQY9z-aRbil0Dq4zmzE2aauF-nGFbJVJkeoHoxi9CldUcJrPjW1uYcPfBaZtUG2c4Xc2SYKeY9jzlYuDgCiigssYFxoQBXWRnTgsUEAgXmFz0h3MpYdPhCwUoExQ4BpAYAtAqxhgZXkGN4SPWosJ9IMvhc8mJx0RUWawIub6P5kKA0ysGmG8PGgKxASBlaQDwdj-m6DmNBn_wDn8m0-ZAcAAA]]

==Software==
The printer runs [[Rebuild]] with Fluidd. The Retool A2 runs Klipper's stock RP2040 firmware, which Rebuild installs and keeps in step with the host.

==Klipper configuration==
The Recore A8 uses the reference config that comes with Rebuild (<code>rebuild-reference/generic-recore-a8.cfg</code>), with the Fluidd config and the toolhead config included from <code>printer.cfg</code>:

<pre>
[include fluidd.cfg]
[include Retool_A2.cfg]
</pre>

The Retool A2 is a separate Klipper MCU, found by its serial number:

<pre>
ls /dev/serial/by-id/
</pre>

Put the path that shows up for the Retool in <code>[mcu retool]</code>. The toolhead config is based on the one used in the [[Voron 2.4]]. Its extruder is called <code>extruder3</code> and its fans have their own names, so it can be included next to the A8 config. The heater, thermistor and PID values still have to be set for the hotend that is fitted, and PID tuned.

==To do==
* Wire diagram and layout
* Toolhead mount and 3D model
* Tested configuration and settings

Main Page

2026-10-14T16:41:02Z

Maintenance script: Link the new Voron 0.1 page under Voron 2.4

{{#tweekihide:navbar-right}}
<div class="res-img">
[[File:Delta H.jpg]]
</div>

This is the documentation for Recore, Manga Screen 1 and 2, Refactor and Toggle hardware and software products developed by made by Intelligent Agent. All software is free and open source. Recore is open schematic hardware and can be conveniently purchased in the store.

{| class="mediawiki" style="width: 100%; vertical-align:top;"
|style="vertical-align:top;"|

== Hardware ==
* [[Recore A8]]
* [[Recore A7]]
* [[Recore A6]]
* [[Remove A1]]
* [[Restep A1]]
* [[Rexfer A0]]
* [[Relit A0]]
* [[Revolt A2]]
* [[Rebase A0]]
* [[Retool_A2]]
* [[Renits_A5]] WIP
* [[Reheat_A0]] WIP

|style="vertical-align:top;"|

==Software==
* [[Rebuild]] Current Linux OS for Recore
* [[Refactor]] Legacy Linux OS for Recore
* [[Reflash]] Image to install Refactor/Rebuild
* [[Mainline Klipper]] How to use the main Klipper release on Recore
* [[Toggle]] User interface for OctoPrint

|style="vertical-align:top;"|

==HowTo==
* [[Getting started]]
* [[Connecting | Connecting to the board]]
* [[Webcams]]
* [[Printer_101 | Printer 101]]
* [[FAQ]]
* [https://discord.gg/bCnp9H5SB5 Discord]
|-
|style="vertical-align:top;"|
====Old hardware====
* [[Replicape Rev B]]
* [[Replicape Rev A]]
* [[Manga Screen 2]]
* [[Manga Screen 1]]
|style="vertical-align:top;"|

====Off site====
* [https://www.klipper3d.org/ Klipper] The "firmware" for Replicape/Recore
* [https://docs.mainsail.xyz/ Mainsail] A modern and responsive user interface for Klipper
* [https://octoprint.org/ OctoPrint ] A snappy web interface for 3D printers
* [https://docs.fluidd.xyz/ Fluidd] Responsive web based user interface for Klipper.
* [https://klipperscreen.readthedocs.io/en/latest/ KlipperScreen] A touchscreen GUI that interfaces with Klipper
|style="vertical-align:top;"|

====Guides====
* [[BLTouch | Using BLTouch with Replicape]]
* [[Adding a Servo | Adding a Servo to Replicape]]
* [[Adding a Probe for G29/G33]]
* [[Cartesian | Cartesian configuration guide]]
* [[Corexy | CoreXY configuration guide]]
* [[OEM_customization | OEM display customisation on Recore]]
* [[Voron_2.4 | Voron 2.4 wiring]]
* [[Voron_0.1 | Voron 0.1 wiring]] WIP
* [[AI-assisted contributions | Submitting AI-assisted code]]
|-
|style="vertical-align:top;"|

== Development ==
* [[ Dev Team Bios | Development Team ]]
* [[Beta Testing | Running the Develop Branch on Your Printer]]

|style="vertical-align:top;"|

== Contributing ==
* [[Special:CreateAccount | Add new users to this wiki]]
* [[Formatting | Formatting on this wiki]]

|style="vertical-align:top;"|
== Legacy Information ==
* [[Thing]]
* [[Thing Delta]]
|}

Voron 0.1

2026-10-14T16:40:54Z

Maintenance script: New page: Voron 0.1 (work in progress)