Rebuild v1.0.0 - Revision history

Elias: Elias moved page Rebuild to Rebuild v1.0.0: New version

2024-06-11T19:40:12Z

Elias moved page Rebuild to Rebuild v1.0.0: New version

2024-06-06T17:29:24Z

2024-06-06T17:26:57Z

2024-06-06T17:23:46Z

2024-06-06T12:50:08Z

‎Getting started

2024-05-30T18:44:17Z

‎Wifi Access Point does work

2024-05-28T13:55:41Z

‎Update u-boot on Recore

2024-05-26T20:55:06Z

‎SSH access

2024-05-26T20:54:29Z

‎SSH access

2024-05-23T22:21:24Z

‎Connecting to an external Wifi access point

@@ Line 75: / Line 75: @@
 # Select wifi network and enter credentials
 # Exit nmtui and verify connection to the wifi network with '''ip addr''' (If you connect via wifi hotspot, you will be disconnected)
 <div class="res-img">
 [[File:Nmtui.gif]]

@@ Line 65: / Line 65: @@
 If you have a Wifi dongle connected, you can connect to a local Wifi access point by using the '''nmtui'''  program.
 ===='''Using nmtui'''====
 nmtui is a Text UI tool to assist in managing network settings.

@@ Line 63: / Line 63: @@
 === Connecting to an external Wifi access point ===
-If you have a Wifi dongle connected, you can connect to a local Wifi access point by using the (using sudo) '''nmtui'''  program.
+If you have a Wifi dongle connected, you can connect to a local Wifi access point by using the '''nmtui'''  program.
 # Use SSH or the serial port to log in to the device.
-# Start the nmtui program
+# Start '''nmtui'''
-# Delete the hotspot connection
+# Select Activate connection
-# Choose Activate connection and choose the Wifi hotspot you want to connect to
+# Select wifi network and enter credentials
 == Recore booting ==

@@ Line 44: / Line 44: @@
 After the Klipper configuration is complete, do a test print to make sure everything is working.
 <div class="alert alert-success">
 ===='''Important'''====

@@ Line 314: / Line 314: @@
 === Wifi Access Point does work ===
 On Rebuild v1.0.0 there is an issue with setting up Wifi as a hotspot/Access Point. There are three issues preventing this.
 # The kernel has trouble with the RTW88 driver causing the AP to connect/disconnect continously. The workaround to that is to downgrade a legacy kernel. The "current" kernel is Linux 6.6.x, while the legacy is 6.1.x as of this writing.

← Older revision	Revision as of 19:40, 11 June 2024
(No difference)

@@ Line 186: / Line 186: @@
 Flash the binary
 <pre>
-dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk0 bs=1024 seek=8 conv=notrunc
+dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2 bs=1024 seek=8 conv=notrunc
 </pre>
 ===AR100 firmware===

@@ Line 118: / Line 118: @@
 # You can start the SSH service from Mainsail/Fluidd
 SSH access is only enabled for user '''debian''' using the password '''temppwd'''.
-The first time you log in, you will be prompted to change the password. After the password has been changed, you will need to log in again. If you do not log in within an hour of enabling SSH, the SSH access will be disabled. This is for security reasons, it's not good to have an open SSH port with the default password. If the SSH access is disabled, it can be enabled again from the user interface.
+The first time you log in, you will be prompted to change the password. After the password has been changed, you will need to log in again. If you do not log in within an hour of enabling SSH, '''the SSH access will be disabled'''. This is for security reasons, it's not good to have an open SSH port with the default password. If the SSH access is disabled, it can be enabled again from the user interface.
 ==Serial port acccess==