Restep A1 - Revision history

Elias: /* Mounting it on Recore */

2024-05-21T13:31:06Z

‎Mounting it on Recore

2024-05-21T13:26:07Z

‎Mounting it on Recore

2024-05-21T13:25:41Z

‎Mounting it on Recore

2024-05-21T13:25:18Z

‎Mounting it on Recore

2024-01-31T11:13:39Z

‎Choosing address

2024-01-31T11:12:47Z

‎Choosing address

2024-01-31T11:12:17Z

‎Choosing address

2024-01-31T11:07:28Z

‎Klipper Configuration Recore A5 and A6

2024-01-31T11:06:55Z

‎Choosing address

2024-01-31T11:04:37Z

@@ Line 10: / Line 10: @@
 </div>
-=== Mounting it on Recore ===
+=== Mounting Restep on Recore ===
-Restep should be mounted so the stepper is pointing upwards and the 6 pin header is pointing down. The 6 pin female header goes into the header on the board marked S6 or S7.
+Restep must be mounted in two different ways, depending on how the 6-pin header is soldered.
 <div class="res-img">
 [[File:Restep mounting.png]]

@@ Line 12: / Line 12: @@
 === Mounting it on Recore ===
 Restep should be mounted so the stepper is pointing upwards and the 6 pin header is pointing down. The 6 pin female header goes into the header on the board marked S6 or S7.
-[[File:Restep mounting.png|thumb|center]]
+<div class="res-img">
 === Choosing address ===

@@ Line 12: / Line 12: @@
 === Mounting it on Recore ===
 Restep should be mounted so the stepper is pointing upwards and the 6 pin header is pointing down. The 6 pin female header goes into the header on the board marked S6 or S7.
-[[File:Restep mounting.png]]
+[[File:Restep mounting.png|thumb|center]]
 === Choosing address ===

@@ Line 11: / Line 11: @@
 === Mounting it on Recore ===
 Restep should be mounted so the stepper is pointing upwards and the 6 pin header is pointing down. The 6 pin female header goes into the header on the board marked S6 or S7.
 === Choosing address ===

@@ Line 18: / Line 18: @@
 It is only necessary to change the address if you are going to use two Resteps on a Recore A6
 </div>
-<div class="res-img">
+[[File:Cut here.png|thumb|center]]
 If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1).

@@ Line 35: / Line 35: @@
 === Klipper Configuration Recore A5 and A6 ===
-In this example, the X-axis is routed to S7. Only the relevant changes are shown.
+In this example, the X-axis is routed to S6. Only the relevant changes are shown.
 <pre>
 [tmc2209 stepper_x]

@@ Line 14: / Line 14: @@
 === Choosing address ===
-If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1).
+<div class="alert alert-warning">
 === Klipper Configuration Recore A7 ===

@@ Line 1: / Line 1: @@
-Restep is an add-on board for [[Recore A6]] which gives it an extra TMC2209 stepper driver. This is great if you want to build a 3D-printer with 7 motors, like the Voron 2.4.
+Restep is an add-on board for [[Recore A6]] and [[Recore A7]] which gives it an extra TMC2209 stepper driver. This is great if you want to build a 3D-printer with 7 motors, like the Voron 2.4.
 <div class="res-img">
 [[File:Restep A1 front.jpg]]