Difference between revisions of "Mainsail"
From iagent
(Created page with " ==On Replicape == 2. ssh in replicape with user "debian" 3. start kiauh: "cd kiauh" and "kiauh.sh" 4. in kiauh: select "1: Install" then "2: Moonraker" (Moonraker ist API fo...") |
(→On Replicape) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
==On Replicape == | ==On Replicape == | ||
| − | + | These are some instructions that have been floating around on the Discord, use at your own risk. | |
| − | + | # ssh in replicape with user "debian" | |
| − | + | # start kiauh: "cd kiauh" and "kiauh.sh" | |
| − | + | # in kiauh: select "1: Install" then "2: Moonraker" (Moonraker ist API for the comunication between klipper and mainsail) | |
| − | + | # after installation "moonraker", install "3: Mainsail" | |
| − | + | # Leave kiah with "q", kiauh will disable octoprint | |
| − | + | # follow the docu at "https://docs.mainsail.xyz/setup/manual-setup/klipper" | |
| − | + | # edit /etc/systemd/system/klipper.service with "nano" ad add "-a /tmp/klippy_uds" to the end of the arg, | |
| − | + | # restart sevices "sudo service klipper restart" and "sudo service moonraker restart" | |
| − | + | # remove port forwarding from octoprint: "nft flush ruleset" and disable it "systemctl mask nftables.service" (thx, goeland86) | |
| − | + | # edit & create the config files like described in "https://docs.mainsail.xyz/setup/manual-setup" | |
| − | + | # if moonraaker cant connect to klipper, reinstall klipper: "cd" than "cd klipper" than "cd scripts" than "./install-beaglebone.sh" | |
| − | + | # restart sevices "sudo service klipper restart" and "sudo service moonraker restart" | |
| − | + | # check if you can load the web ui | |
| + | # thats it, Folks | ||
==On Recore== | ==On Recore== | ||
| − | + | <pre> | |
ssh root@recore.local | ssh root@recore.local | ||
su debian | su debian | ||
cd /home/debian/kiauh | cd /home/debian/kiauh | ||
./kiauh.sh | ./kiauh.sh | ||
| − | + | </pre> | |
| − | Install moonraker | + | Install moonraker |
| − | Install mainsail | + | Install mainsail |
Disable octoprint | Disable octoprint | ||
Latest revision as of 19:03, 29 September 2021
On Replicape
These are some instructions that have been floating around on the Discord, use at your own risk.
- ssh in replicape with user "debian"
- start kiauh: "cd kiauh" and "kiauh.sh"
- in kiauh: select "1: Install" then "2: Moonraker" (Moonraker ist API for the comunication between klipper and mainsail)
- after installation "moonraker", install "3: Mainsail"
- Leave kiah with "q", kiauh will disable octoprint
- follow the docu at "https://docs.mainsail.xyz/setup/manual-setup/klipper"
- edit /etc/systemd/system/klipper.service with "nano" ad add "-a /tmp/klippy_uds" to the end of the arg,
- restart sevices "sudo service klipper restart" and "sudo service moonraker restart"
- remove port forwarding from octoprint: "nft flush ruleset" and disable it "systemctl mask nftables.service" (thx, goeland86)
- edit & create the config files like described in "https://docs.mainsail.xyz/setup/manual-setup"
- if moonraaker cant connect to klipper, reinstall klipper: "cd" than "cd klipper" than "cd scripts" than "./install-beaglebone.sh"
- restart sevices "sudo service klipper restart" and "sudo service moonraker restart"
- check if you can load the web ui
- thats it, Folks
On Recore
ssh root@recore.local su debian cd /home/debian/kiauh ./kiauh.sh
Install moonraker Install mainsail Disable octoprint