Difference between revisions of "Remote A0"
From iagent
(Created page with "<pre> [mcu remote] serial: /dev/serial/by-id/usb-Klipper_rp2040_E661AC8863441226-if00 [output_pin fan_r_0] pin: remote:gpio2 [output_pin fan_r_1] pin: remote:gpio16 [output...") |
|||
| Line 100: | Line 100: | ||
probe_points: | probe_points: | ||
100, 100, 20 # an example | 100, 100, 20 # an example | ||
| + | </pre> | ||
| + | |||
| + | ===Recompile Klipper firmware=== | ||
| + | <pre> | ||
| + | |||
</pre> | </pre> | ||
Latest revision as of 12:49, 20 March 2024
[mcu remote]
serial: /dev/serial/by-id/usb-Klipper_rp2040_E661AC8863441226-if00
[output_pin fan_r_0]
pin: remote:gpio2
[output_pin fan_r_1]
pin: remote:gpio16
[output_pin fan_r_2]
pin: remote:gpio0
[output_pin fan_r_3]
pin: remote:gpio13
[output_pin heater_r_1]
pin: remote:gpio12
[tmc2209 stepper_x]
uart_pin: remote:gpio8
uart_address: 0
run_current: 0.500
hold_current: 0.500
stealthchop_threshold: 250
[stepper_x]
step_pin: remote:gpio6
dir_pin: remote:gpio5
endstop_pin: remote:gpio4
enable_pin: !remote:gpio10
rotation_distance: 40
microsteps: 16
position_endstop: 0
position_max: 200
homing_speed: 20.0
#[tmc2209 extruder3]
#uart_pin: remote:gpio8
#uart_address: 0
#run_current: 0.500
#hold_current: 0.500
#stealthchop_threshold: 250
#[extruder3]
#step_pin: remote:gpio6
#dir_pin: remote:gpio5
#heater_pin: remote:gpio1
#sensor_type: EPCOS 100K B57560G104F
#sensor_pin: remote:gpio27
#rotation_distance: 40
#microsteps: 16
#nozzle_diameter: 0.400
#filament_diameter: 1.75
#control: pid
#pid_Kp: 22.2
#pid_Ki: 1.08
#pid_Kd: 114
#min_extrude_temp: 30
#min_temp: -272
#max_temp: 300
[verify_heater extruder3]
check_gain_time: 2400
[adc_temperature remote_fan_current_0]
temperature1: 0
voltage1: 0
temperature2: 33
voltage2: 3.3
[temperature_sensor remote_fan_current_0]
adc_voltage: 3.3
sensor_pin: remote:gpio29
sensor_type: remote_fan_current_0
max_temp: 2.0
gcode_id: RemoteFanCurrent0
[adc_temperature remote_fan_current_1]
temperature1: 0
voltage1: 0
temperature2: 33
voltage2: 3.3
[temperature_sensor remote_fan_current_1]
adc_voltage: 3.3
sensor_pin: remote:gpio28
sensor_type: remote_fan_current_1
max_temp: 2.0
gcode_id: RemoteFanCurrent1
[adxl345]
cs_pin: remote:gpio21
spi_bus: spi0d
[resonance_tester]
accel_chip: adxl345
probe_points:
100, 100, 20 # an example