Manual control and testing

From iagent
Revision as of 23:14, 26 May 2022 by Elias (talk | contribs) (Created page with "=Manual control and testing= All functions on Recore are meant to be controlled from a graphical user interface such as OctoPrint, Fluid or Mainsail etc. This in turn in contr...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Manual control and testing

All functions on Recore are meant to be controlled from a graphical user interface such as OctoPrint, Fluid or Mainsail etc. This in turn in controlled by Klipper. Sometimes it can be beneficial to get low level access to certain functions and test things directly on the command line. This section is meant to give an overview of what capabilites are available from the command line (SSH/terminal).

Power domain overview

Power domain overview.png

Power domains

There are 9 power domains around the board controlling voltage on different pins:

  • Input power controls power to 4 high power outputs, the 4 fans and the 6 stepper drivers. This input has current monitoring, fast acting over current protection, voltage monitoring, temperature monitoring and reverse polarity protection.
  • Thermo couple power Controls +5V/1A output to the ADCs. This can be used for turning on power to the analog pins.
  • End stop power Controls +5V/1A output on the six endstops. Ganged. ES0 can be switched to have 12V output. The 12V output has a

100mA internal current limit.

  • 4 USB host power domains Controls 5V/1A current output to the usb host connectors. These are turned on by u-boot.
  • HDMI 5V output Controls the 5V/1A HDMI output. Turned on by u-boot.

Input stage

Reset over current protection and set it in "one-shot" mode.

gpioset 1 164=0
gpioset 1 164=1

The over current protection can also be set in "transparent" mode, where the current alarm will be reset automatically. Note that this is a bad idea for general operation, only use for testing.

gpioset 1 164=0

Enable 24V input

gpioset 1 165=0

End stop 5V /12V

End stop 0 to 4 has a programmable +5V output voltage. End stop 5 has +5V or +12V selectable.

To enable +5V on ES 1...5

gpioset 1 162=1

To disable again

gpioset 1 162=0

To switch to 12V output on ES0

gpioset 1 160=1

To disable again

gpioset 1 160=0

End stops values

To see what value the end stops have

gpioget 1 228 # ES 5
gpioget 1 229
gpioget 1 230
gpioget 1 231
gpioget 1 232
gpioget 1 233 # ES 0

TMC2209

In window/shell 1:

stty -F /dev/ttyS2 raw -echoe -echo
xxd -c 4 /dev/ttyS2

In window/shell 2:

echo -n -e '\x5\x0\x6\x6F' > /dev/ttyS2

The return should be along the lines of

00000000: 0500 066f  ...o
00000004: 05ff 0620  ... 
00000008: 0001 4058  ..@X

To check that no errors are reported by the steppers write this on the command line. If a "1" shows up, that is an indication that the motor is reporting an error.

gpioget 1 128
gpioget 1 129
gpioget 1 130
gpioget 1 131
gpioget 1 132
gpioget 1 133

STM32F031

There is a small firmware to test all functionality that is controlled by the STM32F031 chip on the board. Once uploaded to the board using the flash script, the firmware will turn on all LEDs it controls and send back ADC readings.

To flash this firmware to the STM32:

gpioset 1 197=1
gpioset 1 196=0
stm32flash -i -196,196 -w Sumato-f031.bin -v -g 0x00 /dev/ttyS1
gpioset 1 197=0
stm32flash -i -196,196 /dev/ttyS1

To see the ADC readings:

stty -F /dev/ttyS3 38400 raw
cat /dev/ttyS3

You should see something like

ADC T0: 0
ADC T1: 0
ADC T2: 0
ADC T3: 0
ADC U: 2338
ADC I: 0
ADC TB: 3417

The following one-liners assumes gawk is installed.

Reading Current

There is board current reading implemented in OctoPrint. The current shunt resistor is 1 mOhm, the amplifier is 20 times, the vref is 3.3V, so we get: (adc_val/4096*3.3)*1000/20 = (adc_val/4096)*165

If the testing firmware is installed on the STM32, you can convert the current (as in amps) reading to something useful like this:

cat /dev/ttyS4 | awk '/I:/ { printf "scale=4; (%i/4096)*165\n", $3; fflush(); }' | bc -l

Current limit programming

The current limit must be set in the device tree by programming the voltage on dldo2. dldo2 can have values from 0.7 V to 3.4 V. Setting the voltage level to 3.4 V effectively disables the fast acting current limit. Setting it to the lowest value gives an over current limit of 35 A.

Reading Board Temperature

To see the temperature readings, try this :

export beta=4327
cat /dev/ttyS1 | awk '/TB:/ { printf "scale=4; 4327/l( (4700/((3.3/(3.3*%i/4096))-1.0))/0.05306820342563400000) -273.15\n", $3; fflush(); }' | bc -l | awk '{print strftime("%k:%M:%S"), $0; fflush();}'

Reading Input Voltage

To see voltage on the input, it can be converted like this:

exec 4</dev/ttyS4 5>/dev/ttyS4
echo -n ";A4;" >&5
read -t1 reply <&4
echo $reply | awk '{ printf "scale=4; (%i/4096)*3.3*((100+10)/10)\n", $4; fflush(); }' | bc -l

Thermistor inputs

To enable pull-up on input for using thermistors for temperature measurements:

gpioset 1 202=1
gpioset 1 203=1
gpioset 1 204=1
gpioset 1 205=1

Setting Op-amp gain to 1:

gpioset 1 100=0
gpioset 1 235=0
gpioset 1 145=0
gpioset 1 34=0

Setting Op-amp gain to 100:

gpioset 1 100=1
gpioset 1 235=1
gpioset 1 145=1
gpioset 1 34=1

Adding a 0.33 V offset to the input:

gpioset 1 192=1
gpioset 1 193=1
gpioset 1 194=1
gpioset 1 200=1

Do not add 0.33 V offset to the input:

gpioget 1 192
gpioget 1 193
gpioget 1 194
gpioget 1 200

In the device tree file, the gpio/ldos must be set to gpio input:

&gpio0_ldo {
  function = "gpio_in";
};

Thermocouple input

Either a thermocouple or a thermistor can be used as input on the T0-T3 inputs.

Bias

The thermocouple is set up to have a Bias of 0.7V/100 on the input which enables negative values (lower than the board temperature) as input to the ADCs. With the input short circuited, the bias can be recorded. Typical values are 750 This needs to be subtracted from the result.

Cold junction compensation

Another important aspect is cold junction compensation. There is a thermistor connected on the board close to the thermocouple inputs which can be used to measure the temperature close to the input junction. This temperature must be added in software.

The connected thermistor is a TDK NTCG104EF104FT1X The connected Thermocouple has a (25/100) beta value of 4327 K and a (25/85) beta value of 4308 K. The 25/85 beta value is what is used in Klipper.

In order to use the inputs for thermocouple, the pull-up-down resistors must be set to pull-down:

gpioset 1 102=0
gpioset 1 120=0
gpioset 1 160=0
gpioset 1 161=0

Also, the op-amp needs a gain of 100:

gpioset 1 100=0
gpioset 1 235=0
gpioset 1 145=0
gpioset 1 34=0

Finally, the input bias needs to be enabled. The following LDOs needs to be enabled:

reg_ldo_io0
reg_ldo_io1
reg_dldo3
reg_dldo4