Difference between revisions of "Restep A1"
From iagent
(→Klipper Configuration) |
(→Mounting it on Recore) |
||
| (11 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | Restep is an add-on board for [[Recore A6]] which gives it an extra TMC2209 stepper driver. This is great if you want to build a 3D-printer with 7 motors, like the Voron 2.4. | + | Restep is an add-on board for [[Recore A6]] and [[Recore A7]] which gives it an extra TMC2209 stepper driver. This is great if you want to build a 3D-printer with 7 motors, like the Voron 2.4. |
<div class="res-img"> | <div class="res-img"> | ||
[[File:Restep A1 front.jpg]] | [[File:Restep A1 front.jpg]] | ||
| Line 5: | Line 5: | ||
| − | + | === Pinout diagram === | |
<div class="res-img"> | <div class="res-img"> | ||
[[File:Restep A1 pinout.png|center]] | [[File:Restep A1 pinout.png|center]] | ||
</div> | </div> | ||
| − | + | === Mounting Restep on Recore === | |
| − | Restep should be mounted so the stepper is pointing | + | Restep must be mounted in two different ways, depending on how the 6-pin header is soldered. |
| + | # If the pin header is soldered on the component side, the board should be mounted so that the 4-pin header where the stepper motor connects is pointing out the same way as the permanently mounted stepper motors. | ||
| + | # If the pin header is soldered on the bottom of the PCB (where no components are soldered), the 4-pin header where the stepper motor connects should be pointing in towards the center of Recore. | ||
| − | ==== Choosing address ==== | + | <div class="res-img"> |
| − | If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1). | + | [[File:Restep mounting.png]] |
| + | </div> | ||
| + | |||
| + | === Choosing address === | ||
| + | <div class="alert alert-warning"> | ||
| + | ===='''Note'''==== | ||
| + | It is only necessary to change the address if you are going to use two Resteps on a Recore A6 | ||
| + | </div> | ||
| + | [[File:Cut here.png|thumb|center]] | ||
| + | If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1). | ||
| + | |||
| + | === Klipper Configuration Recore A7 === | ||
| + | In this example, the X-axis is routed to S6. Only the relevant changes are shown. | ||
| + | <pre> | ||
| + | [tmc2209 stepper_x] | ||
| + | uart_pin: ar100:PD2 | ||
| + | uart_address: 3 | ||
| + | |||
| + | # Route stepper X to header S6 | ||
| + | [stepper_x] | ||
| + | step_pin: ar100:PL10 | ||
| + | dir_pin: ar100:PE14 | ||
| + | </pre> | ||
| − | + | === Klipper Configuration Recore A5 and A6 === | |
| − | In this example, the X-axis is routed to | + | In this example, the X-axis is routed to S6. Only the relevant changes are shown. |
<pre> | <pre> | ||
[tmc2209 stepper_x] | [tmc2209 stepper_x] | ||
uart_pin: ar100:PD1 | uart_pin: ar100:PD1 | ||
| − | |||
uart_address: 3 | uart_address: 3 | ||
Latest revision as of 13:31, 21 May 2024
Restep is an add-on board for Recore A6 and Recore A7 which gives it an extra TMC2209 stepper driver. This is great if you want to build a 3D-printer with 7 motors, like the Voron 2.4.
Contents
Pinout diagram
Mounting Restep on Recore
Restep must be mounted in two different ways, depending on how the 6-pin header is soldered.
- If the pin header is soldered on the component side, the board should be mounted so that the 4-pin header where the stepper motor connects is pointing out the same way as the permanently mounted stepper motors.
- If the pin header is soldered on the bottom of the PCB (where no components are soldered), the 4-pin header where the stepper motor connects should be pointing in towards the center of Recore.
Choosing address
Note
It is only necessary to change the address if you are going to use two Resteps on a Recore A6
If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1).
Klipper Configuration Recore A7
In this example, the X-axis is routed to S6. Only the relevant changes are shown.
[tmc2209 stepper_x] uart_pin: ar100:PD2 uart_address: 3 # Route stepper X to header S6 [stepper_x] step_pin: ar100:PL10 dir_pin: ar100:PE14
Klipper Configuration Recore A5 and A6
In this example, the X-axis is routed to S6. Only the relevant changes are shown.
[tmc2209 stepper_x] uart_pin: ar100:PD1 uart_address: 3 # Route stepper X to header S6 [stepper_x] step_pin: ar100:PL10 dir_pin: ar100:PE14