Difference between revisions of "Restep A1"
(→Klipper Configuration) |
|||
| Line 16: | Line 16: | ||
If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1). | If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1). | ||
| − | === Klipper Configuration === | + | === Klipper Configuration Recore A7 === |
| + | In this example, the X-axis is routed to S6. Only the relevant changes are shown. | ||
| + | <pre> | ||
| + | [tmc2209 stepper_x] | ||
| + | uart_pin: ar100:PD2 | ||
| + | uart_address: 3 | ||
| + | |||
| + | # Route stepper X to header S6 | ||
| + | [stepper_x] | ||
| + | step_pin: ar100:PL10 | ||
| + | dir_pin: ar100:PE14 | ||
| + | </pre> | ||
| + | |||
| + | === Klipper Configuration Recore A5 and A6 === | ||
In this example, the X-axis is routed to S7. Only the relevant changes are shown. | In this example, the X-axis is routed to S7. Only the relevant changes are shown. | ||
<pre> | <pre> | ||
[tmc2209 stepper_x] | [tmc2209 stepper_x] | ||
uart_pin: ar100:PD1 | uart_pin: ar100:PD1 | ||
| − | |||
uart_address: 3 | uart_address: 3 | ||
Revision as of 11:03, 31 January 2024
Restep is an add-on board for Recore A6 which gives it an extra TMC2209 stepper driver. This is great if you want to build a 3D-printer with 7 motors, like the Voron 2.4.
Contents
Pinout diagram
Mounting it on Recore
Restep should be mounted so the stepper is pointing upwards and the 6 pin header is pointing down. The 6 pin female header goes into the header on the board marked S6 or S7.
Choosing address
If you only have one Restep board mounted on Recore, you do not have to alter it in any way. The default UART address will then be 3. If you want to add one more board, you can cut the lines on AD0 which will give the board address 2. Address 0 and 1 are reserved for stepper 4 and 5 which are mounted on the board on UART3(pins PD0/PD1).
Klipper Configuration Recore A7
In this example, the X-axis is routed to S6. Only the relevant changes are shown.
[tmc2209 stepper_x] uart_pin: ar100:PD2 uart_address: 3 # Route stepper X to header S6 [stepper_x] step_pin: ar100:PL10 dir_pin: ar100:PE14
Klipper Configuration Recore A5 and A6
In this example, the X-axis is routed to S7. Only the relevant changes are shown.
[tmc2209 stepper_x] uart_pin: ar100:PD1 uart_address: 3 # Route stepper X to header S6 [stepper_x] step_pin: ar100:PL10 dir_pin: ar100:PE14