Search results

Create the page "Hardware" on this wiki! See also the search results found.

Main Page
...gent Agent. All software is free and open source. Recore is open schematic hardware and can be conveniently purchased in the store. == Hardware ==

2 KB (314 words) - 17:28, 16 May 2026
Manga Screen 1
Make sure hardware flow control is set to OFF in minicom. Backlight is adjusted from 1 to 255. Manga Screen has been designed to be easily reprogrammed. All software and hardware is open source and available from the repository.

12 KB (1,972 words) - 10:08, 29 September 2022
Replicape Rev A
This page is about the hardware. When you have the hardware mounted, take a look a the [http://wiki.thing-printer.com/images/replicape_ == Hardware source files ==

10 KB (1,679 words) - 17:01, 20 October 2018
Replicape Rev B
This page is about the hardware. When you have the hardware mounted, take a look a the [http://wiki.thing-printer.com/images/replicape_ == Hardware source files ==

10 KB (1,676 words) - 19:04, 20 October 2018
Dev Team Bios
...efforts around the Kamikaze/Redeem/Toggle environment, and of course, the Hardware of Thing-Printer :)

2 KB (298 words) - 18:08, 19 October 2018
Redeem settings
Calibrating Redeem for your 3D printer's hardware.

31 KB (4,743 words) - 16:13, 20 October 2018
Refactor v3.0.2
...e user the ability to choose which firmware/software stack to run on their hardware. The following pre-build declinations are planned:

14 KB (2,381 words) - 12:55, 8 December 2021
Recore A5
This document is for Recore Revision A5. For previous hardware revisions, please see: ==Hardware overview==

27 KB (3,867 words) - 20:45, 17 June 2024
Refactor v3.0.3
...e user the ability to choose which firmware/software stack to run on their hardware. The following pre-build declinations are planned:

19 KB (3,075 words) - 09:12, 9 April 2022
Refactor v3.1.3
Note: On Refactor 3.2.x, all hardware revisions communicate with the MCU (STM32) on UART /dev/ttyS2. This was dif

15 KB (2,431 words) - 23:27, 4 December 2023
Refactor
On Refactor 3.2.x, all hardware revisions communicate with the MCU (STM32) on UART /dev/ttyS2. This was dif

14 KB (2,216 words) - 13:45, 15 December 2023
Recore A3
==Hardware overview==

22 KB (3,282 words) - 08:52, 28 May 2024
Recore A2
==Hardware overview==

12 KB (1,921 words) - 17:29, 20 January 2022
Recore A4
This document is for Recore Revision A4. For previous hardware revisions, please see: ==Hardware overview==

26 KB (4,020 words) - 12:57, 29 February 2024
AR100
# Make a soft/bitbang implementation on different pins. This will require a hardware change from rev A2.

10 KB (1,806 words) - 08:34, 9 August 2021
Recore A6
This document is for Recore Revision A6. For previous hardware revisions, please see: ...ly the two USB host ports next to the HDMI port is powered. See also known hardware issues at the [[Recore_A6#USB_connectors_not_discovered_when_powered_by_USB

26 KB (4,244 words) - 10:22, 24 January 2024
Recore A7
This document is for Recore Revision A7. For previous hardware revisions, please see: ...is the ADXL345. This can be connected to the connectors S6/S7. There is no hardware SPI interface available, but a software implementation in Klipper exists.

30 KB (4,806 words) - 14:06, 14 May 2024
Refactor 3.2
On Refactor 3.2.x, all hardware revisions communicate with the MCU (STM32) on UART /dev/ttyS2. This was dif Reflash will create a symlink to the device tree for the hardware version of the board.

14 KB (2,296 words) - 16:42, 1 December 2023
Revolt A1
==Hardware connections==

2 KB (351 words) - 23:06, 14 February 2024
Refactor 3.1
Note: On Refactor 3.2.x, all hardware revisions communicate with the MCU (STM32) on UART /dev/ttyS2. This was dif

15 KB (2,449 words) - 23:24, 4 December 2023