User contributions for Elias

20 October 2018

• 21:3121:31, 20 October 2018 diff hist +16 Getting started →How do I get started?
• 21:2821:28, 20 October 2018 diff hist −392 Toggle →Angstrom
• 21:2821:28, 20 October 2018 diff hist −87 Toggle →Software stack overview
• 20:3820:38, 20 October 2018 diff hist −140 Umikaze →Starting up current
• 20:3820:38, 20 October 2018 diff hist +6 N File:Etcher.png No edit summary current
• 20:3520:35, 20 October 2018 diff hist +13 Main Page No edit summary
• 20:3320:33, 20 October 2018 diff hist +2 Main Page No edit summary
• 20:3220:32, 20 October 2018 diff hist −291 Main Page →Legacy Information
• 20:3220:32, 20 October 2018 diff hist +1,640 N Beta Testing Created page with "Congratulations! You have chosen to become one of the few, the proud, the guinea pigs! Before you switch to the develop branch of Redeem, it's probably best to check on the #..." current
• 20:3120:31, 20 October 2018 diff hist +2,107 N Adding a Probe for G29/G33 Created page with "===Intro=== So you're ready to auto-calibrate your Delta, or you just want to run a bed leveling routine on your Cartesian or CoreXY? Well, in order to do this, you're going t..." current
• 20:3120:31, 20 October 2018 diff hist +1,112 N Adding a Servo Created page with "== So you want to use a servo with your Replicape...== This is a very easy process! '''Step 1:''' Connect your servo to the X2 (or Y2) connection on your Replicape <img src=..." current
• 20:3020:30, 20 October 2018 diff hist +2,550 N BLTouch Created page with "= Introduction = BLTouch is a simple-to-use bed probe from the folks at ANTCLabs. It's simple because it senses and moves a probe-pin with an electromagnet, which gives it a..." current
• 20:3020:30, 20 October 2018 diff hist +10,325 N Marlin to redeem Created page with "= From Marlin to Redeem = == Understanding the difference between Marlin and Redeem == Redeem is a completely new 3d printer controller. It's been optimized to run on the Be..." current
• 20:2920:29, 20 October 2018 diff hist −7 Main Page →Guides
• 20:2820:28, 20 October 2018 diff hist 0 Main Page No edit summary
• 20:2820:28, 20 October 2018 diff hist +245 N Getting started Created page with "==How do I get started?== # Wire up your 3D printer to the Replicape or Revolve. # Install Umikaze on the BeagleBone Black or Revolve. # Connect to the device [..."
• 20:2820:28, 20 October 2018 diff hist +22 Main Page →HowTo
• 20:2720:27, 20 October 2018 diff hist −246 Printer 101 No edit summary
• 20:2720:27, 20 October 2018 diff hist −20 Printer 101 →How do I get started?
• 20:2520:25, 20 October 2018 diff hist +15 Main Page →HowTo
• 20:2020:20, 20 October 2018 diff hist +58 Main Page →Off site
• 20:1920:19, 20 October 2018 diff hist +17 Main Page →Software
• 20:1720:17, 20 October 2018 diff hist +5,159 N Replicape Rev B techspecs Created page with "= Tech Specs = == Steppers == There are five [http://www.trinamic.com/products/integrated-circuits/stepper-power-driver/tmc2100 TMC2100] Stepper Motor Controllers (SMDs) on..." current
• 19:4819:48, 20 October 2018 diff hist −106 Manga Screen 2 No edit summary
• 19:4719:47, 20 October 2018 diff hist +47 Manga Screen 2 No edit summary
• 19:4719:47, 20 October 2018 diff hist +19 N File:MS2-first-prototype.jpg No edit summary current
• 19:4619:46, 20 October 2018 diff hist +42 Manga Screen 2 No edit summary
• 19:4519:45, 20 October 2018 diff hist +16 N File:Render back both.png No edit summary current
• 19:3319:33, 20 October 2018 diff hist −22 Manga Screen 2 No edit summary
• 19:3219:32, 20 October 2018 diff hist −1 Manga Screen 2 No edit summary
• 19:3019:30, 20 October 2018 diff hist −55 Manga Screen 2 No edit summary
• 19:2919:29, 20 October 2018 diff hist +12 N File:Front-render.png No edit summary current
• 19:1119:11, 20 October 2018 diff hist −2 Manga Screen 2 No edit summary
• 19:1119:11, 20 October 2018 diff hist +12 N File:ISO-render-2.png No edit summary current
• 19:0419:04, 20 October 2018 diff hist −2 Replicape Rev B →Hardware source files current
• 19:0319:03, 20 October 2018 diff hist −44 Replicape Rev B →How to wire up the board
• 19:0219:02, 20 October 2018 diff hist +24 N File:Replicape-wire-diagram-2.png No edit summary current
• 17:0417:04, 20 October 2018 diff hist −93 Replicape Rev B No edit summary
• 17:0317:03, 20 October 2018 diff hist +16 N File:Replicape B2 top.png No edit summary current
• 17:0117:01, 20 October 2018 diff hist −40 Replicape Rev A No edit summary current
• 17:0117:01, 20 October 2018 diff hist −54 Replicape Rev A No edit summary
• 17:0017:00, 20 October 2018 diff hist +25 N File:Render-top.png No edit summary current
• 16:1716:17, 20 October 2018 diff hist +268 Formatting No edit summary
• 16:1416:14, 20 October 2018 diff hist +26 Main Page →Contributing
• 16:1316:13, 20 October 2018 diff hist +9 Redeem settings No edit summary current
• 16:1216:12, 20 October 2018 diff hist −2 Redeem settings →Initial Configuration
• 16:1116:11, 20 October 2018 diff hist −112 Redeem settings →Initial Configuration
• 16:0716:07, 20 October 2018 diff hist +46 Redeem settings →Initial Configuration
• 16:0616:06, 20 October 2018 diff hist +23 N File:Octoprint redeem plugin.png No edit summary current
• 16:0516:05, 20 October 2018 diff hist +1,472 Redeem settings No edit summary